ASSRA Forum - Need wall thickness RWS 8.15x46R brass

ASSRA Forum › General › Reloading the Single Shot Rifle › Need wall thickness RWS 8.15x46R brass

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

Need wall thickness RWS 8.15x46R brass (Read 2122 times)

Skalkaho Oldtimer Offline Posts: 863 Location: Montana Joined: Sep 29^th, 2006	Need wall thickness RWS 8.15x46R brass Nov 5^th, 2018 at 10:33am	Print Post
	Making up some 8.15x46R out of 30-30 brass,with a wall thickness of .008. I'd like to know the wall thickness of RWS brass 815.46R.Thanks
	« Last Edit: Nov 5^th, 2018 at 11:55am by Skalkaho »
	May the Bullet Gods be with you.......
	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 4473 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: Need wall thickness RKS 8.15x46R brass Reply #1 - Nov 5^th, 2018 at 11:51am	Print Post
	If you mean RWS brass, I don't have any, but I measured some DWM and it measured .008 to .009 at the neck.


	IP Logged

Skalkaho Oldtimer Offline Posts: 863 Location: Montana Joined: Sep 29^th, 2006	Re: Need wall thickness RWS 8.15x46R brass Reply #2 - Nov 5^th, 2018 at 11:59am	Print Post
	LOL...sonic cleaning 32 RKS brass this morning also working on a Buchel,Thanks,Pete

	May the Bullet Gods be with you.......
	IP Logged

Fred Boulton Oldtimer Offline Posts: 801 Joined: Jan 6^th, 2007	Re: Need wall thickness RWS 8.15x46R brass Reply #3 - Nov 5^th, 2018 at 12:01pm	Print Post
	I use both RWS brass and some made from 30-30. measuring wall thickness with a Vernier is not exactly super accurate, but it makes a good gauge and I can confirm that they are the same. Fred


	IP Logged

Skalkaho Oldtimer Offline Posts: 863 Location: Montana Joined: Sep 29^th, 2006	Re: Need wall thickness RWS 8.15x46R brass Reply #4 - Nov 5^th, 2018 at 12:06pm	Print Post
	Thanks Fred. Have a oversize neck chamber,if I had .010 brass it would help .Am leaving more brass up the case into the lead to get a smaller dia to hold bullet. Pete

	May the Bullet Gods be with you.......
	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 4473 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: Need wall thickness RWS 8.15x46R brass Reply #5 - Nov 5^th, 2018 at 12:52pm	Print Post
	Is it chambered for a stop ring bullet? That excess space could be for the stop ring and the clearance in the neck could be to allow the stop ring bullet to just slip in. Also, I measured the necks on some made from old WW 32 Win brass and they were more like .006.


	IP Logged

Skalkaho Oldtimer Offline Posts: 863 Location: Montana Joined: Sep 29^th, 2006	Re: Need wall thickness RWS 8.15x46R brass Reply #6 - Nov 6^th, 2018 at 9:38am	Print Post
	With a .008 neck neck thickness,fireformed in chamber,A 323 bullet swims around,would take a .325! With the bore at .318 thats quite A difference. By going out A little longer on the case can get it to just slip fit a .320 bullet,more to my liking. Will be testing fixed,with stop ring bullet,and breech seating. There could be 1/4" of dead air space with breech.More later.Thankyou,Pete.

	May the Bullet Gods be with you.......
	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 0.7504 seconds.