ASSRA Forum › General › General Discussion › LYMAN SCOPE MOUNT
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 2 3 [4]  Send TopicPrint
Very Hot Topic (More than 25 Replies) LYMAN SCOPE MOUNT (Read 11513 times)
LONG RANGE
Senior Forum Member
****
Offline



Posts: 414
Location: CHERRY VALLEY, CA
Joined: Oct 3rd, 2013
Re: LYMAN SCOPE MOUNT
Reply #45 - Nov 6th, 2018 at 3:00pm
Print Post  
I started this post with the question , how to take apart the adjustment thimble on the Lyman STS scope? After all the response, I still don't know. Since you men have replaced the pad on the adjustment screw, did you take it apart to do the work? If so, how did you do it?
  
Back to top
 
IP Logged
 
LONG RANGE
Senior Forum Member
****
Offline



Posts: 414
Location: CHERRY VALLEY, CA
Joined: Oct 3rd, 2013
Re: LYMAN SCOPE MOUNT
Reply #46 - Nov 6th, 2018 at 3:01pm
Print Post  
I started this post with the question , how to take apart the adjustment thimble on the Lyman STS scope? After all the response, I still don't know. Since you men have replaced the pad on the adjustment screw, did you take it apart to do the work? If so, how did you do it?
  
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7428
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: LYMAN SCOPE MOUNT
Reply #47 - Nov 6th, 2018 at 3:38pm
Print Post  
LR,
This is the answer to your question.
frnkeore wrote on Oct 28th, 2018 at 2:00pm:
This is from Jack's link:

At this point it took me a while to figure how to disassemble further. After digging out all the old grease from the inside of 3 I realized there was a common screw slot in there. I took a chance on trying to turn it in the conventional direction but it wouldn't budge. I added some more Kroil and let it set for a few hours. It finally loosened and out came part 2. Part 2 has internal threads that engage the threaded post on part 6. Once 2 is removed, everything comes apart."

Frank

  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
LONG RANGE
Senior Forum Member
****
Offline



Posts: 414
Location: CHERRY VALLEY, CA
Joined: Oct 3rd, 2013
Re: LYMAN SCOPE MOUNT
Reply #48 - Nov 6th, 2018 at 7:37pm
Print Post  
Frank, could you tell me how to get part 1 out of part 3? Thanks, Glen
  
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7428
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: LYMAN SCOPE MOUNT
Reply #49 - Nov 7th, 2018 at 1:17am
Print Post  
Glen,
It looks like it will slide out.

I don't know if I have any of that type, most if not all of mine have the bar type, tube contact area.

I'll look tomorrow and see if I have any nylon type turrets.

Frank
  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
LONG RANGE
Senior Forum Member
****
Offline



Posts: 414
Location: CHERRY VALLEY, CA
Joined: Oct 3rd, 2013
Re: LYMAN SCOPE MOUNT
Reply #50 - Nov 7th, 2018 at 6:12pm
Print Post  
Frank, mine looks exactly like the one posted by RSW taken apart and numbered.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1 2 3 [4] 
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.7532 seconds.