ASSRA Forum › General › Reloading the Single Shot Rifle › Load for a 45-70 Peabody?
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Load for a 45-70 Peabody? (Read 2342 times)
is0086s
Full Member
***
Offline


Bob Ryan

Posts: 151
Location: minnesota
Joined: Nov 10th, 2004
Load for a 45-70 Peabody?
Jul 13th, 2018 at 9:14pm
Print Post  
I have recently come into a 45-70 peabody rifle. It's in very nice condition. I want to shoot it but am worried about recoil. I'd appreciate suggestions for load that won't recoil heavily. Bullet mould? Bullet weight? Powder type / weight? I have no experience with the 45-70. Fear of hungry lawyers aside, I'd appreciate any suggestions.
  
Bob Ryan
Back to top
 
IP Logged
 
Hiwall55
Senior Forum Member
****
Offline



Posts: 468
Location: west central Illinois
Joined: Jun 30th, 2012
Re: Load for a 45-70 Peabody?
Reply #1 - Jul 14th, 2018 at 6:40am
Print Post  
A gent has one he shoots at our club,400 grain bullet with 2400 powder. Its very accurate.
  
Back to top
 
IP Logged
 
ten-mile
Full Member
***
Offline



Posts: 165
Location: Chetek
Joined: Dec 8th, 2007
Re: Load for a 45-70 Peabody?
Reply #2 - Jul 14th, 2018 at 7:26am
Print Post  
I have one of the Peabody-Martini carbines in 45-70.  I shoot 300 grain bullets and the recoil is not at all bad.  Lyman 457191 and the Saeco or RCBS 300s all shoot very well.  Use published Trapdoor loads and be happy.
  
Back to top
WWW  
IP Logged
 
George Babits
Frequent Elocutionist
*****
Offline



Posts: 1151
Joined: Sep 27th, 2012
Re: Load for a 45-70 Peabody?
Reply #3 - Jul 14th, 2018 at 9:38am
Print Post  
You didn't mention which Peabody you have in 45-70.  Is it a Connecticut Militia model?  If so, you will probably find that the bore is a bit over size.  I have one and had the dickens of a time finding an accurate black powder load. I would have to dig out my notes to be sure, but think the groove diameter is around 0.461 or there abouts.   I didn't have a mould that size so went to a soft lead paper patched bullet of about 460 grains.  Shoots very accurately and recoil is not all that bad.

I have another Peabody which was originally a "Spanish" model with a trashed chamber.  I had that rebarreled to 45-70 and it shoots quite well.  I have been using the Lyman 457193 bullet (420 grains) and it works quite well.  Haven't tried smokless powder in it.

George
  
Back to top
 
IP Logged
 
is0086s
Full Member
***
Offline


Bob Ryan

Posts: 151
Location: minnesota
Joined: Nov 10th, 2004
Re: Load for a 45-70 Peabody?
Reply #4 - Jul 15th, 2018 at 11:06am
Print Post  
It is a conn militia rifle. I will be shooting smokeless and lead. Are these rifles gain wist?
  
Bob Ryan
Back to top
 
IP Logged
 
John in PA
Oldtimer
*****
Offline



Posts: 590
Location: Hollidaysburg, PA
Joined: Nov 3rd, 2009
Re: Load for a 45-70 Peabody?
Reply #5 - Aug 17th, 2018 at 8:25pm
Print Post  
Connecticut models have Henry rifling. It is not gain twist.  None of the Peabody's, sporting or military,  have factory gain twist rifling.
  
John Wells
Hollidaysburg, PA
Peabody and Peabody-Martini's Wanted!
Back to top
 
IP Logged
 
LONG RANGE
Senior Forum Member
****
Offline



Posts: 414
Location: CHERRY VALLEY, CA
Joined: Oct 3rd, 2013
Re: Load for a 45-70 Peabody?
Reply #6 - Aug 17th, 2018 at 9:02pm
Print Post  
For years I have loaded 15 grains of Unique behind a 300 grain Lyman bullet with no complaints. MY 45-70s are a Pedersoli and an original Trapdoor.
  
Back to top
 
IP Logged
 
JWDreamstone
Participating Member
*
Offline



Posts: 37
Location: Long Branch, New Jersey
Joined: Oct 11th, 2017
Re: Load for a 45-70 Peabody?
Reply #7 - Sep 18th, 2018 at 9:45pm
Print Post  
I have a Conn peabody 45/70 I purchases this with a broken firing pin. recently sent it to Frank @ Peabody. for repair.  Finally got it to the range . Using 24 gn AA5744 behind with a 405 cast 
Shot and Grouped very well @ 100.Yds. plan on Moving Up to 500 Gn.cast
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.2474 seconds.