ASSRA Forum - beeswax wads in fixed bpcr ammo

ASSRA Forum › General › Reloading the Single Shot Rifle › beeswax wads in fixed bpcr ammo

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

beeswax wads in fixed bpcr ammo (Read 2449 times)

bruce moulds Senior Forum Member Offline Posts: 290 Location: the antipodes Joined: Mar 14^th, 2015	beeswax wads in fixed bpcr ammo Apr 17^th, 2017 at 12:32am	Print Post
	has anyone tried this with greasers or pp? good gas seal? any help as a lubricant? how thick is ideal? keep safe, bruce.

	ventum est amicus meus
	IP Logged

Schuetzenmiester Frequent Elocutionist Offline Posts: 6707 Location: Cool Wet Side of WA Joined: Apr 27^th, 2008	Re: beeswax wads in fixed bpcr ammo Reply #1 - Apr 17^th, 2017 at 1:16am	Print Post
	I tried it with greasers many years ago. Didn't seem to make any difference.

	"some old things are lovely, warm still with life ... of the forgotten men who made them." - D.H. Lawrence
	IP Logged

bruce moulds Senior Forum Member Offline Posts: 290 Location: the antipodes Joined: Mar 14^th, 2015	Re: beeswax wads in fixed bpcr ammo Reply #2 - Apr 17^th, 2017 at 6:25am	Print Post
	thank you. that is what some others have also told me. what do others think? the martini 577/450 was loaded with wax and card wads only, and was shot dirty. refer to rourke's drift. could the wax offer a good seal for starting bore diamer bullets? keep safe, bruce.

	ventum est amicus meus
	IP Logged

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3987 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Re: beeswax wads in fixed bpcr ammo Reply #3 - Apr 17^th, 2017 at 8:22am	Print Post
	Hmmm. I use 1/8" cork under the bullet (in several calibers) scrapes the bore clean every shot. (using smokeless as Unique, 4227 etc.)

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

MartiniBelgian Frequent Elocutionist Offline Posts: 1734 Location: Aarschot Joined: Jun 7^th, 2004	Re: beeswax wads in fixed bpcr ammo Reply #4 - Apr 17^th, 2017 at 3:15pm	Print Post
	Well, it would for sure stop gas cutting... And the brits went to greqt lengths in component design to make sure the wad would expand...


	WWW IP Logged

.22-5-40 Oldtimer Offline Posts: 828 Joined: Feb 13^th, 2010	Re: beeswax wads in fixed bpcr ammo Reply #5 - Apr 17^th, 2017 at 4:15pm	Print Post
	In a Ballard .25-25 Stevens, I am using a thin 1/32" beeswax wad on top of drop tubed powder, 1/8" grease cookie, another 1/32" b.w. wad & 1/16" veg. fiber wad under bullet. Another variant is 1/32" b.w. wad on powder. Puff-Lon filled to case mouth & compressed by bullet seating. In both above loadings, Swiss 3FG is used, no compression. Best accuracy is with 1 barely damp patch thru bore after each shot..bore left damp.


	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 1.2242 seconds.