ASSRA Forum - .32 miller short case length

ASSRA Forum › General › Reloading the Single Shot Rifle › .32 miller short case length

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

.32 miller short case length (Read 2208 times)

bcovell Participating Member Offline Posts: 22 Location: Florida Joined: Dec 1^st, 2005	.32 miller short case length Apr 1^st, 2017 at 2:32pm	Print Post
	I am getting ready to make some .32 Miller short cases. Could someone tell me what is the official case length for a .32 miller short. thanks

	Bob C&&&&bcffr3931k@hotmail.com
	IP Logged

blk43 Junior Member Offline Posts: 69 Location: Lodi, California Joined: Apr 26^th, 2008	Re: .32 miller short case length Reply #1 - Apr 1^st, 2017 at 2:39pm	Print Post
	Mine measure 1.275 and have a few firings on them. Have you measured the reamer? Bruce

	BLK
	IP Logged

bcovell Participating Member Offline Posts: 22 Location: Florida Joined: Dec 1^st, 2005	Re: .32 miller short case length Reply #2 - Apr 1^st, 2017 at 5:00pm	Print Post
	I just picked up a Ruger #1 that has been rebarreled and chambered in .32 miller short. I need to make some cases for it.

	Bob C&&&&bcffr3931k@hotmail.com
	IP Logged

bpjack Frequent Elocutionist Online Posts: 3335 Location: East Olympia, WA Joined: May 18^th, 2008	Re: .32 miller short case length Reply #3 - Apr 1^st, 2017 at 5:14pm	Print Post
	I measured some 357 converted to 32 Miller and they run 1.275 to 1.280. I BS. I also only breech seat. Jack

	ASSRA # 11318 There are more hydrogen atoms in a single molecule of water than there are suns in the entire solar system.
	IP Logged

bnice Frequent Elocutionist Offline Posts: 1919 Location: Iowa Joined: Nov 30^th, 2006	Re: .32 miller short case length Reply #4 - Apr 1^st, 2017 at 6:02pm	Print Post
	1.274"


	IP Logged

dave_j Full Member Offline Posts: 246 Location: Nevada desert Joined: Jul 12^th, 2005	Re: .32 miller short case length Reply #5 - Apr 3^rd, 2017 at 2:37pm	Print Post
	1.275 is best but i went down to 1.260 and with a flared case mouth there was no difference in poi seat the bullet out further, what is the difference???

	ah heck AA#9,4227,300MP, as long as it goes bang
	IP Logged

40_Rod Frequent Elocutionist Offline Extremism in the persuit of accuracy is not a vice Posts: 4285 Location: Knoxville, TN Joined: Apr 20^th, 2004	Re: .32 miller short case length Reply #6 - Apr 4^th, 2017 at 8:56am	Print Post
	Reamer print shows 1.22 to the base of the rim. So its 1.22 plus your rim for OAL. 40 Rod


	IP Logged

Bob259 Participating Member Offline Posts: 24 Joined: Nov 25^th, 2017	Re: .32 miller short case length Reply #7 - Oct 8^th, 2025 at 12:26pm	Print Post
	Ok how much do they grow after forming from 357 max cases, what should I cut them down to before forming them so they are at the correct length after forming. Thanks in advance!


	IP Logged

calledflyer Frequent Elocutionist Offline Posts: 3804 Joined: Mar 9^th, 2015	Re: .32 miller short case length Reply #8 - Oct 8^th, 2025 at 5:24pm	Print Post
	don't attempt to trim and form to the final length. simpler, and surer, to rough it and fire form and THEN trim to final length.


	IP Logged

bnice Frequent Elocutionist Offline Posts: 1919 Location: Iowa Joined: Nov 30^th, 2006	Re: .32 miller short case length Reply #9 - Oct 9^th, 2025 at 2:57pm	Print Post
	Also the 360 Dan Wesson cases are shorter then max cases but are suppose to have the heavier web like the max, Much less to trim


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.7401 seconds.