ASSRA Forum - .25 rim fire

ASSRA Forum › General › General Discussion › .25 rim fire

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1] 2

Hot Topic (More than 10 Replies)

.25 rim fire (Read 8002 times)

Hank45 Oldtimer Offline Beer is living proof that GOD loves you Posts: 506 Location: MA Joined: Jan 21^st, 2010	.25 rim fire May 11^th, 2015 at 12:46pm	Print Post
	Does any body still manufacture 25 rim fire ammo? Thanks for your answer, Hank


	IP Logged

ssdave Frequent Elocutionist Offline Posts: 1768 Location: Eastern Oregon Joined: Apr 16^th, 2004	Re: .25 rim fire Reply #1 - May 11^th, 2015 at 12:59pm	Print Post
	Was last made in the 1960's by CIL in Canada. dave


	IP Logged

slumlord44 Frequent Elocutionist Offline Posts: 2849 Location: Lebanon, Illinois 62254 Joined: Dec 21^st, 2007	Re: .25 rim fire Reply #2 - May 11^th, 2015 at 8:42pm	Print Post
	There are some alternatives that have been discussed at length here if you do a search.


	IP Logged

John Boy Ex Member	Re: .25 rim fire Reply #3 - May 11^th, 2015 at 10:34pm	Print Post
	The easiest way to substitute for 25 RF ammunition is: * Buy 22 Hornet cases * Resize them to 25 Hornet * Trim Hornet cases to 1.125 * Load with either a low charge of Unique or with 10grs black powder


	IP Logged

ten-mile Full Member Offline Posts: 163 Location: Chetek Joined: Dec 8^th, 2007	Re: .25 rim fire Reply #4 - May 12^th, 2015 at 6:57am	Print Post
	A neighbor has about 45 .25 shorts (CIL) he would sell for $50 plus the UPS. From estate of one of his friends. They looked in decent condition.


	WWW IP Logged

ron Oldtimer Offline Posts: 576 Location: Augusta Maine Joined: Nov 15^th, 2009	Re: .25 rim fire Reply #5 - May 12^th, 2015 at 8:05am	Print Post
	John Boy, Will there be enough primer area for the firing pin to make a good hit ,or would there have to be work done to the action? ron


	IP Logged

ron Oldtimer Offline Posts: 576 Location: Augusta Maine Joined: Nov 15^th, 2009	Re: .25 rim fire Reply #6 - May 12^th, 2015 at 8:08am	Print Post
	John Boy. Would there be enough primer area for the firing pin to make a good hit, or would the action need to be worked on? ron


	IP Logged

uscra112 Frequent Elocutionist Offline Posts: 4079 Location: Switzerland of Ohio Joined: May 7^th, 2007	Re: .25 rim fire Reply #7 - May 12^th, 2015 at 8:30am	Print Post
	Answer is no. The .25 RF firing pin is too far off center. What rifle? Some are ridiculously easy to rework to hit a centerfire primer, others not. (Notably the Stevens 44 and Favorites) There's a bunch of guys using powder-actuated tool cartridges with breech-seated bullets, others are machining the shortened .25 Hornet cases to take a .22 blank as the primer. A .25RF firing pin will almost always give a concentrically located .22 RF rim a good hit.

	<div class=
	IP Logged

John Boy Ex Member	Re: .25 rim fire Reply #8 - May 12^th, 2015 at 9:01am	Print Post
	Quote: Will there be enough primer area for the firing pin to make a good hit ,or would there have to be work done to the action? The block was bushed for the firing pin hole on the Stevens Favorite


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 15997 Location: Oregon Joined: Feb 2^nd, 2009	Re: .25 rim fire Reply #9 - May 12^th, 2015 at 10:47am	Print Post
	Quote: The easiest way to substitute for 25 RF ammunition is: * Buy 22 Hornet cases * Resize them to 25 Hornet * Trim Hornet cases to 1.125 * Load with either a low charge of Unique or with 10grs black powder Wouldn't this also require the chamber to be reamed to the Hornet also? And if so, do you ream it to .22 Hornet, or is a specialty reamer needed to convert to .25 Hornet?

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

uscra112 Frequent Elocutionist Offline Posts: 4079 Location: Switzerland of Ohio Joined: May 7^th, 2007	Re: .25 rim fire Reply #10 - May 12^th, 2015 at 1:48pm	Print Post
	The nominal base diameter of .25 Stevens RF was .276". The measured base diameter of new Hornet brass from my larder is .293". What I would do is to swage the base of the Hornet brass down, using a .25ACP die. This isn't a lot, by comparison with some I've done, but it will leave a little fillet just above the rim, which would be turned off in a lathe. A drill press and a sharp file will do pretty well for that in a pinch. You'd need a good hefty press. An RCBS Junior would be about the minimum. If the BB has already been bushed, remove that bushing and make another one that aligns the pin for centerfire. This can be done on a drill press, but a small vertical mill is much better. Reaming the chamber presents problems. The .25 Hornet pilot won't fit for starters. The reamer would have to be held short by .690 to get the length right. Chamber will come out small, since the .25 Hornet case is tapered.

	<div class=
	IP Logged

bisaacson Full Member Offline Posts: 170 Location: Kailua Joined: Sep 1^st, 2009	Re: .25 rim fire Reply #11 - May 12^th, 2015 at 10:05pm	Print Post
	Been there, done that with a Stevens Marksman; the whole story is in the June 2010 issue of the Single Shot Exchange, and last time I checked, they still had back issues. Use a .22 case for priming with reformed brass. Works just fine if the gun is in reasonably good condition.


	IP Logged

uscra112 Frequent Elocutionist Offline Posts: 4079 Location: Switzerland of Ohio Joined: May 7^th, 2007	Re: .25 rim fire Reply #12 - May 12^th, 2015 at 10:54pm	Print Post
	bisaacson wrote on May 12^th, 2015 at 10:05pm: Been there, done that with a Stevens Marksman; the whole story is in the June 2010 issue of the Single Shot Exchange, and last time I checked, they still had back issues. Use a .22 case for priming with reformed brass. Works just fine if the gun is in reasonably good condition. Marksman, yes. THAT was the best boy's rifle Stevens ever made, IMHO. Stronger than the Favorite. And it came in a centerfire version, too!

	<div class=
	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 15997 Location: Oregon Joined: Feb 2^nd, 2009	Re: .25 rim fire Reply #13 - May 13^th, 2015 at 11:17am	Print Post
	I think I'll leave my Ballard in .25 Stevens as is. It was rebored by Stevens to the .25, and I've got 4-5 boxes of ammo. Not sure I want to go to this much changing to fire this one gun. I can shoot others, and leave it as a curiosity.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

John Boy Ex Member	Re: .25 rim fire Reply #14 - May 13^th, 2015 at 3:53pm	Print Post
	Edited the Steps: Been many months and had to retrace my steps Here's the process I use to make 25 Stevens reloads: * Trim 1.403 length on 22 Hornets down to 1.130 * Run 22 Hornet brass in a 25 Hornet FL sizing die - to reduce the web * Run the cases into a 25 Hornet Expander die to expand the case just past the shoulder * Re-run the cases back into a 25 Hornet FL sizing die * Fireform the brass * Trim brass to 1.125, the case length of a 25 Stevens * Reloaded with either 7-8-9grs BP (original BP charge 10-11grs) and 3-4grs of 2400 smokeless using the Lyman 257420 - 72gr bullet Results that the reloads drop into the chamber with ease (You need to *Login* or *Register* to view media files and links)
	« Last Edit: May 13^th, 2015 at 10:12pm by »

	IP Logged

Page Index Toggle

Pages: [1] 2

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.4637 seconds.