ASSRA Forum - Breach seater manufacture question

ASSRA Forum › General › General Discussion › Breach seater manufacture question

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

Breach seater manufacture question (Read 2661 times)

is0086s Full Member Offline Bob Ryan Posts: 151 Location: minnesota Joined: Nov 10^th, 2004	Breach seater manufacture question Apr 9^th, 2015 at 10:03am	Print Post
	I an going to make a breach seater for a high wall 38-55. I have made seaters for 32-40 and 25-20 SS before. On the ones I've previously made the case is loose on the push rod. In pictures and ads that the cases seem to be attached solidly. How is this done? JB weld (or equivalent)? Solder? A threaded connector?

	Bob Ryan
	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: Breach seater manufacture question Reply #1 - Apr 9^th, 2015 at 10:21am	Print Post
	Bob are you saying you want it to be non adjustable? If so you can drill and tap the case and thread it onto the end of the push rod and locktite it. It would be best if it was adjustable but the case would have to float on the seater stem so you can insert the bullet and seat it central to the bore. JLouis

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

frnkeore Frequent Elocutionist Offline Posts: 7627 Location: Central Point, OR 97502 Joined: Jun 16^th, 2010	Re: Breach seater manufacture question Reply #2 - Apr 9^th, 2015 at 3:13pm	Print Post
	The BSer can be made adjustable and attached to the body of the BSer. Use a 1/4" plunger rod, drill and tap the case 5/16 x 24 with either a chamfer of thread relief to get it to butt against the BS body. Case heads are about .200 long so, the threads don't need to longer than that. The stadard drill size is and I (.272) but you still get 50% thread with a 9/32 drill and that should hold the case fine and give a thicker wall for the BS body to rod for support. Your plunger will have to be all brass or a brass insert on the bullet end, threaded or pressed on. Your case will still stay on the BSer w/o threading, if you use the 1/4" plunger rod and a bullet size insert, larger than the rod. It will be able to move fore and aft but, will remain on the BSer. Frank

	ASSRA Member #696, ISSA Member #339
	YIM AIM IP Logged

is0086s Full Member Offline Bob Ryan Posts: 151 Location: minnesota Joined: Nov 10^th, 2004	Re: Breach seater manufacture question Reply #3 - Apr 10^th, 2015 at 9:16am	Print Post
	My apologies to the group. I seem to have lost my ability to communicate. My question is not about adjustability. The seaters I make are adjustable. They are mechanical, not push type seaters. The question I am trying to ask is how to attach the case to the front of the seater body.

	Bob Ryan
	IP Logged

Kurt_701 Frequent Elocutionist Offline Posts: 1050 Location: Missouri Joined: May 20^th, 2004	Re: Breach seater manufacture question Reply #4 - Apr 10^th, 2015 at 11:07am	Print Post
	Russ Weber drills and taps the case which is threaded on to the seater body. Kurt

	M-14 3rd Battalion 27th Marines RVN 68'69'
	IP Logged

is0086s Full Member Offline Bob Ryan Posts: 151 Location: minnesota Joined: Nov 10^th, 2004	Re: Breach seater manufacture question Reply #5 - Apr 12^th, 2015 at 12:24pm	Print Post
	kurt_701: Many thanks! That's just the info I want.

	Bob Ryan
	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 1.5220 seconds.