ASSRA Forum - 32-40 Transport to range

ASSRA Forum › General › General Discussion › 32-40 Transport to range

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

32-40 Transport to range (Read 3663 times)

Brudford01 Full Member Offline Posts: 196 Location: Beaver Falls PA Joined: May 18^th, 2008	32-40 Transport to range Mar 1^st, 2015 at 9:23am	Print Post
	If I were to use a MTM Case_Guard plastic box , what size box with a lid will securely hold the 32-40 cases ? Thanks


	IP Logged

DWT1885 Senior Forum Member Offline Posts: 467 Location: New Jersey Joined: Nov 25^th, 2010	Re: 32-40 Transport to range Reply #1 - Mar 1^st, 2015 at 9:30am	Print Post
	I like the MTM R-100 box. Has a handle on top. I use the cork method in the shell and add a sheet of foam to the top of the box. Works like a charm. Dale.

	35th Security Police Squadron, Phan Rang AB, RVN, May 70-71. All gave some, some gave all.
	IP Logged

win 32-40 Ex Member	Re: 32-40 Transport to range Reply #2 - Mar 1^st, 2015 at 9:54am	Print Post
	I like the Caseguard 50 which is made for it along with the other Win 94 cals , about 1/4 in. clearance on length in case your loads are a little long


	IP Logged

Pentz Senior Forum Member Offline Funf und Zwanzig mit den Hut Posts: 435 Location: Vancouver, WA Joined: Sep 4^th, 2014	Re: 32-40 Transport to range Reply #3 - Mar 1^st, 2015 at 10:39am	Print Post
	I'm a belt and suspenders guy; wrap a cinch strap through the handle and around the box as well. I've seen those open with catastrophic results when not latched correctly. THAT will ruin your day!

	ASSRA Member Yoostabe # 11497
	IP Logged

QuestionableMaynard8130 Frequent Elocutionist Offline Posts: 4144 Location: Benton Harbor MI Joined: Apr 17^th, 2004	Re: 32-40 Transport to range Reply #4 - Mar 1^st, 2015 at 12:49pm	Print Post
	Are you asking about fixed load ammo, or empty, or primed/charged/corked case containers?

	sacred cows make the best burger
	IP Logged

Brudford01 Full Member Offline Posts: 196 Location: Beaver Falls PA Joined: May 18^th, 2008	Re: 32-40 Transport to range Reply #5 - Mar 1^st, 2015 at 1:18pm	Print Post
	32-40 for breech seating loaded with primer and IMR 4227 powder probably with a cork or rubber stopper in the case mouth . 50% of my cases are formed from 30-30 Winchester cases and the other half are true 32-40 marked WCF cases. Would like a snap on lid with a carrying handle and at least a hundred round box .


	IP Logged

jfeldman ASSRA Board Member Offline Posts: 1115 Location: Imperial Beach, Ca Joined: Nov 5^th, 2005	Re: 32-40 Transport to range Reply #6 - Mar 1^st, 2015 at 6:14pm	Print Post
	Plus one on the MTM Case Gard R-100 Regards, Joe


	IP Logged

ron Oldtimer Offline Posts: 576 Location: Augusta Maine Joined: Nov 15^th, 2009	Re: 32-40 Transport to range Reply #7 - Mar 1^st, 2015 at 6:34pm	Print Post
	Try a Plano 30-30, 50 or 100 count case. It has two latch points plus the cover is hinged and it will stay open. Just put a piece of foam to take up the small space that is left over. ron


	IP Logged

JS47 Frequent Elocutionist Offline Posts: 1265 Location: Arizona Joined: Oct 12^th, 2012	Re: 32-40 Transport to range Reply #8 - Mar 1^st, 2015 at 11:30pm	Print Post
	I've been using MTM 210 because that's all I had for 38-55, 4227 with card wad. I had to run the boxes through the bandsaw to cut them off just above the bottom squares. The top needs to be cut down also. It's a bit of a nuisance but it works fine until I get something better. JS


	IP Logged

Seanmp Senior Forum Member Offline Posts: 294 Location: Land O Lakes Joined: May 19^th, 2014	Re: 32-40 Transport to range Reply #9 - Mar 3^rd, 2015 at 8:17am	Print Post
	Your looking for the DELUXE-R-100 Don't forget you can rotate the tray to adjust the tray height

	Sean
	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.6913 seconds.