ASSRA Forum - vv N110 in 32 miller short

ASSRA Forum › General › Reloading the Single Shot Rifle › vv N110 in 32 miller short

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

vv N110 in 32 miller short (Read 3145 times)

Vano Ex Member	vv N110 in 32 miller short Jan 16^th, 2015 at 10:07am	Print Post
	any thoughts on shooting cast bullets in a cpa rifle in the 1400 fps range thanks vano


	IP Logged

Myers Senior Forum Member Offline Posts: 388 Joined: Mar 5^th, 2013	Re: vv N110 in 32 miller short Reply #1 - Jan 16^th, 2015 at 7:43pm	Print Post
	Give it a try. My friend uses the same powder in a 25 schuetzen.


	IP Logged

.22-5-40 Oldtimer Offline Posts: 826 Joined: Feb 13^th, 2010	Re: vv N110 in 32 miller short Reply #2 - Jan 17^th, 2015 at 1:19am	Print Post
	My std. accuracy powder with cast has always been H4227..but I have discovered VVN110 to be just as or slightly better in accuracy and bore is left very clean. This burns slightly slower than H4227, but I find I need to use a gas-checked bullet for accuracy..I need to work some more with this powder & plain-base bullets.


	IP Logged

frnkeore Frequent Elocutionist Offline Posts: 7611 Location: Central Point, OR 97502 Joined: Jun 16^th, 2010	Re: vv N110 in 32 miller short Reply #3 - Jan 17^th, 2015 at 1:56am	Print Post
	I had high hopes for this powder in my 33 ELCO (on the max case), I started just below my best velocity range of 1470 - 80 and when to 1500+ and it didn't do as well as 4227 and 4227 doesn't do well with my chambering. I only tried one primer though, Rem 7 1/2. AA #9 is the only powder that I've tried, that I gives good accuracy. Frank

	ASSRA Member #696, ISSA Member #339
	YIM AIM IP Logged

40_Rod Frequent Elocutionist Offline Extremism in the persuit of accuracy is not a vice Posts: 4285 Location: Knoxville, TN Joined: Apr 20^th, 2004	Re: vv N110 in 32 miller short Reply #4 - Jan 17^th, 2015 at 9:45am	Print Post
	Frank Your experience mirrors mine with N110. Its burn rate is about right and it does burn clean It was just never as accurate as the other powders that I used in the cases I tried it in. I finally gave up on it. 40 Rod


	IP Logged

frnkeore Frequent Elocutionist Offline Posts: 7611 Location: Central Point, OR 97502 Joined: Jun 16^th, 2010	Re: vv N110 in 32 miller short Reply #5 - Jan 17^th, 2015 at 2:54pm	Print Post
	I've always heard good things about V V powders (except price) and I got my sealed #2 can for only $20 I hope others might try it in standard size case and report their finding. I may give it another chance with pistol primers but, unless it's like 4759 I'm not holding out any hope for it. Frank

	ASSRA Member #696, ISSA Member #339
	YIM AIM IP Logged

Schuetzendave Frequent Elocutionist Offline Retired Ex-Shooter Posts: 4227 Location: St. Albert, Alberta Joined: Jan 28^th, 2005	Re: vv N110 in 32 miller short Reply #6 - Jan 17^th, 2015 at 5:26pm	Print Post
	Years ago Ralph MacDonald tested VV N110 in the 32 RKS. It almost performed as well as AA#9, H108 or WC820. However double the cost for it could not justify it's use unless it had greatly improved accuracy (which it never did).


	IP Logged

Vano Ex Member	Re: vv N110 in 32 miller short Reply #7 - Jan 18^th, 2015 at 11:50am	Print Post
	Thanks for input this is a powder that is still up on the pvalley Website pistol powders hard to find Thanks again vano


	IP Logged

RayH Oldtimer Offline ASSRA # 10880 Posts: 756 Location: Oldest City, FL Joined: Jan 4^th, 2012	Re: vv N110 in 32 miller short Reply #8 - Jan 18^th, 2015 at 7:25pm	Print Post
	I've tested with it in my .32-20CPA. Not favorably impressed. Moved on.

	In GOD We Trust
	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.8330 seconds.