ASSRA Forum - I need help with a Remington RB # 2

ASSRA Forum › General › General Discussion › I need help with a Remington RB # 2

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

I need help with a Remington RB # 2 (Read 2043 times)

smoke810 Senior Forum Member Offline Posts: 260 Location: N.E. Oklahoma Joined: May 22^nd, 2004	I need help with a Remington RB # 2 Nov 14^th, 2014 at 7:04pm	Print Post
	I disassembled one some time back to bed a stock and like a dumb a*& didn't take a picture of the removable tang to see how the trigger and parts went back together. Can someone please email me a copy of a schematic for a # 2 . I thought I would remember how it came apart but you know how senility is!! If worse comes to worse I could take another one apart but hopefully someone has a copy. chknspit@cox.net Don G


	IP Logged

BP Frequent Elocutionist Offline Posts: 8039 Location: Westside Joined: Aug 27^th, 2006	Re: I need help with a Remington RB # 2 Reply #1 - Nov 14^th, 2014 at 9:33pm	Print Post
	Don't have a schematic with me at the moment, but going from memory, the lower tang retains the trigger and trigger pin, sear and sear pin and the spring that tensions both the sear and breach block. The flat tail of the sear fits into the notches at the rear of the trigger. Put the main bend of the spring to the front of the trigger guard. The leaf of the spring that has the half circle goes downward, and the trigger pin is installed over the half circle to retain both the spring and the trigger in the lower tang.

	There are three kinds of men: The ones that learn by reading, the few who learn by observation, and the rest who have to pee on the electric fence and find out for themselves. Proud Noodlehead
	IP Logged

oughtsix Global Moderator ASSRA Board Member Offline Posts: 1370 Location: Columbus Joined: May 31^st, 2009	Re: I need help with a Remington RB # 2 Reply #2 - Nov 14^th, 2014 at 10:44pm	Print Post
	email with pdf on way

	Life Member ASSRA, OGCA & TSGC I'm all in favor of keeping dangerous weapons out the hands of fools. Let's start with typewriters........ Frank Lloyd Wright
	IP Logged

smoke810 Senior Forum Member Offline Posts: 260 Location: N.E. Oklahoma Joined: May 22^nd, 2004	Re: I need help with a Remington RB # 2 Reply #3 - Nov 15^th, 2014 at 9:14am	Print Post
	oughtsix Thanks for your trouble, however, I did not receive your email. Don G


	IP Logged

oughtsix Global Moderator ASSRA Board Member Offline Posts: 1370 Location: Columbus Joined: May 31^st, 2009	Re: I need help with a Remington RB # 2 Reply #4 - Nov 15^th, 2014 at 10:31am	Print Post
	Tried again with a jpg file. If that doesn't work I'll just post on forum.

	Life Member ASSRA, OGCA & TSGC I'm all in favor of keeping dangerous weapons out the hands of fools. Let's start with typewriters........ Frank Lloyd Wright
	IP Logged

smoke810 Senior Forum Member Offline Posts: 260 Location: N.E. Oklahoma Joined: May 22^nd, 2004	Re: I need help with a Remington RB # 2 Reply #5 - Nov 15^th, 2014 at 1:32pm	Print Post
	Alan Been out of pocket the last few hours. I did receive the emails. Thanks a bunch. In the meantime this morning I disassembled another # 2 and found my problem the sear breach block spring (Item # 20) was missing half of the spring. I need to find another one, will start looking for sources. Don G


	IP Logged

oughtsix Global Moderator ASSRA Board Member Offline Posts: 1370 Location: Columbus Joined: May 31^st, 2009	Re: I need help with a Remington RB # 2 Reply #6 - Nov 15^th, 2014 at 4:47pm	Print Post
	Rollingblockparts dot com is where I got mine. Seems like there is one other source but don't remember where. My sear catch on my hammer is chipped, so I need to find a way to fix that or get a new hammer.(not an easy part to find)

	Life Member ASSRA, OGCA & TSGC I'm all in favor of keeping dangerous weapons out the hands of fools. Let's start with typewriters........ Frank Lloyd Wright
	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 1.3749 seconds.