ASSRA Forum - How to remove barrel on 44 1/2?

ASSRA Forum › General › Single Shot Rifles › How to remove barrel on 44 1/2?

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1] 2

Hot Topic (More than 10 Replies)

How to remove barrel on 44 1/2? (Read 10734 times)

Bulseyetom Frequent Elocutionist Offline Posts: 1046 Location: Santa Maria, Ca Joined: Oct 31^st, 2010	How to remove barrel on 44 1/2? Jan 22^nd, 2014 at 11:57pm	Print Post
	OK. question of the day is what is the proper procedure to remove a centerfire barrel from a Stevens 44 1/2? If you open the action will the extractor clear the barrel? How do you hold the action while you turn the barrel or visa versa? I have changed barrels dozens of times on benchrest bolt guns but had action wrenches that fit the action and a padded barrel vice. Thanks for any help or source for a manual. Tom


	Twitter IP Logged

BP Frequent Elocutionist Offline Posts: 8039 Location: Westside Joined: Aug 27^th, 2006	Re: How to remove barrel on 44 1/2? Reply #1 - Jan 23^rd, 2014 at 1:00am	Print Post
	If you open the action, the extractor (or ejector if so equipped for a 22 RF) should clear the extractor notch cut into the barrel. Way I do it is first loosen the barrel retaining screw just enough so you can turn it with your fingers. Then hold the rifle with the barrel muzzle down and buttstock up (you can rest the muzzle for the moment on a soft CLEAN folded towel). Next, open the action fully and make a visual check to confirm the extractor has indeed cleared the extractor notch. Lift the rifle upward so it clears the towel you were resting the muzzle on by a few inches. Then back the barrel retaining screw out far enough with your fingers so you can rotate the barrel. Hold the stock/action steady and unscrew the barrel. Others may do it differently.

	There are three kinds of men: The ones that learn by reading, the few who learn by observation, and the rest who have to pee on the electric fence and find out for themselves. Proud Noodlehead
	IP Logged

bohemianway Oldtimer Offline Posts: 713 Location: Andover, MN Joined: Apr 16^th, 2004	Re: How to remove barrel on 44 1/2? Reply #2 - Jan 23^rd, 2014 at 10:33pm	Print Post
	Just did this on mine. Barrel clamped in milling machine vise and 15" crescent on the action. Note: it is a very tightly fit barrel.


	GTalk IP Logged

ledball Frequent Elocutionist Offline Posts: 1021 Location: syracuse, ohio Joined: Nov 20^th, 2009	Re: How to remove barrel on 44 1/2? Reply #3 - Jan 24^th, 2014 at 9:04am	Print Post
	The breechblock and extractor should be removed from the 44 1/2 Stevens and then the breechblock reinstalled to remove a tight fitting barrel. Reinstalling the block prevents twisting the receiver walls. IMO. Ledball


	IP Logged

rkaires Frequent Elocutionist Offline No Stronger Bond Posts: 1674 Location: Dingmans Ferry, PA Joined: Oct 26^th, 2012	Re: How to remove barrel on 44 1/2? Reply #4 - Jan 24^th, 2014 at 9:47am	Print Post
	bohemianway wrote on Jan 23^rd, 2014 at 10:33pm: Just did this on mine. Barrel clamped in milling machine vise and 15" crescent on the action. Note: it is a very tightly fit barrel. Ouch!

	ASSRA #11031 NRA Life Proud Noodlehead "Peace is that brief, glorious moment in history, when everybody stands around reloading."~ ~ Thomas Jefferson
	IP Logged

RayH Oldtimer Offline Posts: 758 Location: Oldest City, FL Joined: Jan 4^th, 2012	Re: How to remove barrel on 44 1/2? Reply #5 - Jan 24^th, 2014 at 10:37am	Print Post
	Bob, It doesn't hurt a bit! I clamp, with padding, the barrel and flat bottomed BR forend to a solid work table and use a padded fine furniture clamp on the action to gain grip and torque. Never a mark on any part of the rifle and easy as pie!

	In GOD We Trust
	IP Logged

rkaires Frequent Elocutionist Offline No Stronger Bond Posts: 1674 Location: Dingmans Ferry, PA Joined: Oct 26^th, 2012	Re: How to remove barrel on 44 1/2? Reply #6 - Jan 24^th, 2014 at 11:57am	Print Post
	I must be spoiled. Both my 441/2's have barrels that come off with hand pressure only.

	ASSRA #11031 NRA Life Proud Noodlehead "Peace is that brief, glorious moment in history, when everybody stands around reloading."~ ~ Thomas Jefferson
	IP Logged

slumlord44 Frequent Elocutionist Offline Posts: 2850 Location: Lebanon, Illinois 62254 Joined: Dec 21^st, 2007	Re: How to remove barrel on 44 1/2? Reply #7 - Jan 25^th, 2014 at 12:24am	Print Post
	Got a 44 that the barrel is tight in and I want to remove it. Similar procedure should work. They usually come out easily.


	IP Logged

Bulseyetom Frequent Elocutionist Offline Posts: 1046 Location: Santa Maria, Ca Joined: Oct 31^st, 2010	Re: How to remove barrel on 44 1/2? Reply #8 - Jan 25^th, 2014 at 1:34pm	Print Post
	OK, I removed the retaining screw, made sure the extractor cleared the barrel cut and it is more than hand tight. Before I put the bar rel in my barrel vise to hold it while I twist the stock with more leverage I want to make sure that only one screw needs to be removed. I also assume they have a right hand thread. Any other thoughts before I go to Plan B? Thanks. Tom


	Twitter IP Logged

marlinguy Frequent Elocutionist Online Ballards may be weaker, but they sure are neater! Posts: 18327 Location: Oregon Joined: Feb 2^nd, 2009	Re: How to remove barrel on 44 1/2? Reply #9 - Jan 25^th, 2014 at 2:18pm	Print Post
	Bulseyetom wrote on Jan 25^th, 2014 at 1:34pm: OK, I removed the retaining screw, made sure the extractor cleared the barrel cut and it is more than hand tight. Before I put the bar rel in my barrel vise to hold it while I twist the stock with more leverage I want to make sure that only one screw needs to be removed. I also assume they have a right hand thread. Any other thoughts before I go to Plan B? Thanks. Tom I would suggest NOT twisting on the stock to separate the action and barrel! If it's very tight you could damage the stock. Best to clamp the barrel in a barrel vise, and then twist on the action either with a padded action wrench, or a large wood clamp on the action. But be sure to have the block in the action to keep from damaging the walls.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

RayH Oldtimer Offline Posts: 758 Location: Oldest City, FL Joined: Jan 4^th, 2012	Re: How to remove barrel on 44 1/2? Reply #10 - Jan 25^th, 2014 at 3:41pm	Print Post
	25 X !

	In GOD We Trust
	IP Logged

Bulseyetom Frequent Elocutionist Offline Posts: 1046 Location: Santa Maria, Ca Joined: Oct 31^st, 2010	Re: How to remove barrel on 44 1/2? Reply #11 - Jan 25^th, 2014 at 6:42pm	Print Post
	I can see where the breechblock in the action would stiffen things up and prevent tweeking the action so that brings up question number 2...........how do you properly remove the breech and extractor? Are there any springs that will fly of into never to be sen again land? Thanks. Tom


	Twitter IP Logged

ledball Frequent Elocutionist Offline Posts: 1021 Location: syracuse, ohio Joined: Nov 20^th, 2009	Re: How to remove barrel on 44 1/2? Reply #12 - Jan 25^th, 2014 at 7:51pm	Print Post
	No, there are no flying parts, there is a small set-screw that holds the finger lever pin, loosen this set screw, open the action, push the finger lever pin out from either side, the block and extractor can now be pulled out the bottom--when reinserting the block the rear of the firing pin will sometimes need to be pushed in to clear the frame. Ledball


	IP Logged

Bulseyetom Frequent Elocutionist Offline Posts: 1046 Location: Santa Maria, Ca Joined: Oct 31^st, 2010	Re: How to remove barrel on 44 1/2? Reply #13 - Jan 25^th, 2014 at 9:28pm	Print Post
	I will get brave and try that tomorrow! Thanks guys. Tom


	Twitter IP Logged

MAD MIKE Oldtimer Offline Posts: 655 Location: So Cal Joined: Oct 31^st, 2006	Re: How to remove barrel on 44 1/2? Reply #14 - Jan 25^th, 2014 at 10:47pm	Print Post
	Take the fore end off & put the octagon section of the barrel in a vise (padded). Use the milling machine vise on the action (padded). Make sure your extactor is clear & turn CC. Assuming you loosened the barrel retaining screw & removed the scope, the barrel should turn off. Good Luck......MIKE...


	IP Logged

Page Index Toggle

Pages: [1] 2

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.4259 seconds.