ASSRA Forum › General › General Discussion › Tom Rowe Publications
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Tom Rowe Publications (Read 6551 times)
creedmoormatch
Ex Member


Tom Rowe Publications
Apr 20th, 2011 at 12:02pm
Print Post  

     I am seeking contact information either, voice or E-mail, or both for Tom Rowe Publications Co. in Maynardville, Tennessee, prior in Rochester, New York.

     Any help provided would be greatly appreciated and the favor returned.

     Creedmoormatch
  
Back to top
 
IP Logged
 
harry_eales
Ex Member


Re: Tom Rowe Publications
Reply #1 - Apr 20th, 2011 at 12:23pm
Print Post  
CMM,

Send a PM to Whitey Hanson, I'm sure he knows.

Harry
  
Back to top
 
IP Logged
 
whitey hanson
Ex Member


Re: Tom Rowe Publications
Reply #2 - Apr 20th, 2011 at 6:24pm
Print Post  
CMM I do have Toms private Phone #. But would need his permission to give it out. Whitey
  
Back to top
 
IP Logged
 
creedmoormatch
Ex Member


Re: Tom Rowe Publications
Reply #3 - Apr 21st, 2011 at 7:29am
Print Post  

   Whitey

    Russ Weber suggested that I contact Tom for the purchase of a repro Ideal Breech Seater Tool.

   That was my only business with Mr. Rowe.  Thanks anyway, I fully understand and respect his privacy and your integrity.

  Have a good day

   Creedmoormatch
  
Back to top
 
IP Logged
 
Kurt_701
Frequent Elocutionist
*****
Offline



Posts: 1016
Location: Missouri
Joined: May 20th, 2004
Re: Tom Rowe Publications
Reply #4 - Apr 21st, 2011 at 7:30am
Print Post  
Hallowell & Co. 
Lists this as his contact info for rowe Books.
Tom Rowe Books, PO Box 370, Maynardville, TN 37807-0370.  Tel: 423 992-4017

Kurt
  
M-14 3rd Battalion 27th Marines RVN 68'69'
Back to top
 
IP Logged
 
40_Rod
Frequent Elocutionist
*****
Offline


Extremism in the persuit
of accuracy is not a
vice

Posts: 4285
Location: Knoxville, TN
Joined: Apr 20th, 2004
Re: Tom Rowe Publications
Reply #5 - Apr 21st, 2011 at 8:35am
Print Post  
As far as I know Tom now lives in Virginia unless he moved back to Tennessee. If you want an Ideal b.s. tool you need to talk to Bill Loos (585) 544-1027 he used to make them he was / is Tom's partner in the books. 
I have to tell you that the bullet/throat fit required for a push type seater pretty much the same size as the bullet. If I have been reading your posts correctly you are considering using a reduced capacity 32-40 case with the approximate capacity of the 32MS Short / 32X357 Dell. This tells me that you are using smokeless. For smokeless you are going to want to have .001 to .002 at the base of the bullet. I can tell you from experience that the energy required to seat a bullet like that is tiring. For smokeless loads you are going to be a lot better off with a seater form either Singleshot on this forum or Russ Weber. Both of their seaters will let you seat a variety of bullets with minimal effort.

40 Rod
  
Back to top
 
IP Logged
 
Schutzenbob
Frequent Elocutionist
*****
Offline


Rheinisch-Westfälisc
hen Sprengstoff-Fabriken

Posts: 2054
Location: Nightingale, California
Joined: Oct 24th, 2005
Re: Tom Rowe Publications
Reply #6 - May 2nd, 2011 at 3:54pm
Print Post  
Does anyone know when Tom is going to publish his fabled three volume set of books on Harry Pope’s rifles?  Undecided
  
Back to top
 
IP Logged
 
whitey hanson
Ex Member


Re: Tom Rowe Publications
Reply #7 - May 2nd, 2011 at 6:01pm
Print Post  
The last time I talked to Tom about re publishing the British SS. And the New Winfer book. He said Until the economy turned around some things would be slim. When I talk to him again I will ask him and post the information. Whitey
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.2539 seconds.