ASSRA Forum › General › Collecting Single Shot Rifles › .22 L.R. Pope chamber C'bore
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic .22 L.R. Pope chamber C'bore (Read 4159 times)
.22-5-40
Oldtimer
*****
Offline



Posts: 802
Joined: Feb 13th, 2010
.22 L.R. Pope chamber C'bore
Jan 28th, 2011 at 1:57pm
Print Post  
Hello, I am going to have to get a camera!  I was looking over the Pope barreled B.S.A., and was checking out breech area.  I noticed the c'bore for ctg. rim is about .030" wider per side than head of case.  Now these martini actions can't be un-cocked like a hammer gun, must pull trigger while closing block.  & this one has very light pull.  I was wondering if Pope put this extra clearance in there for a reason...perhaps to prevent pin from hitting chamber edge if accidently dry-fired?  What do other Pope rimfire chamber c'bore's  look like?  Thank you.
  
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7332
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: .22 L.R. Pope chamber C'bore
Reply #1 - Jan 28th, 2011 at 2:31pm
Print Post  
Normally, that won't keep the pin off the rim c'bore. Usually you have to put a divit in that part of the chamber to keep that from happening. Most firing pins protude more than the thickness of the 22rf rim.

Frank
  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
Quarter_Bore
Oldtimer
*****
Offline



Posts: 817
Location:   
Joined: Dec 16th, 2005
Re: .22 L.R. Pope chamber C'bore
Reply #2 - Jan 28th, 2011 at 4:36pm
Print Post  
Many old rimfires were made that way. I know Pope's and other originals had the same thing. I have a factory Stevens barrel. It's the same way. It's just how they did it.
  
Back to top
 
IP Logged
 
MartiniBelgian
Frequent Elocutionist
*****
Offline



Posts: 1687
Location: Aarschot
Joined: Jun 7th, 2004
Re: .22 L.R. Pope chamber C'bore
Reply #3 - Jan 29th, 2011 at 3:20am
Print Post  
Maybe in those days tolerances were quite a bit bigger in cartridge manufacturing...
  
Back to top
WWW  
IP Logged
 
screwloosetc
Ex Member


Re: .22 L.R. Pope chamber C'bore
Reply #4 - Jan 29th, 2011 at 1:50pm
Print Post  
My 13/15 and MKll martinis both have the divit for dryfiring at 12:00. 
there is no extra clearance around the rim.
Tom
  
Back to top
 
IP Logged
 
.22-5-40
Oldtimer
*****
Offline



Posts: 802
Joined: Feb 13th, 2010
Re: .22 L.R. Pope chamber C'bore
Reply #5 - Jan 30th, 2011 at 3:06pm
Print Post  
Thanks guy's for helpful reply's, and thank you Quarter bore for informing me Pope did this on others..That is a very big help!  As for that divot..I have seen these and had always thought some kid had got hold of it & used it for play!  Thats what I like about these forums..I always learn something new.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.6138 seconds.