ASSRA Forum › General › General Discussion › case trimmers
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic case trimmers (Read 3926 times)
sportslube
Oldtimer
*****
Offline



Posts: 603
Location: Eau Claire, wi
Joined: May 13th, 2008
case trimmers
Dec 30th, 2009 at 11:00pm
Print Post  
If one was to buy a power case trimmer  would you choose between a forester drill press trimmer  59.00  or the RCBS 250,00 model.  or does one have one for sale less than these prices  I am, not a major trimmer just more for a particular rifle trimmer.  not doing thousands just a few a year type
  
Back to top
 
IP Logged
 
Singleshotlover
Ex Member


Re: case trimmers
Reply #1 - Dec 30th, 2009 at 11:25pm
Print Post  
I have a forster, wilson and a lot of lee case trimmers with lock stud. Guess which one see's the most use. The lee's. Stick the lock stud in a cordless drill, insert the trimmer and done deal. I find the lee setup faster than either wilson or forster. Frank
  
Back to top
 
IP Logged
 
40_Rod
Frequent Elocutionist
*****
Offline


Extremism in the persuit
of accuracy is not a
vice

Posts: 4285
Location: Knoxville, TN
Joined: Apr 20th, 2004
Re: case trimmers
Reply #2 - Dec 31st, 2009 at 8:14am
Print Post  
I have used a Forster trimmer for years. If I am going to do a lot of cases I unscrew the handle, put on a nut and use a power screwdriver with a nut driver mounted. it works great.

40 Rod
  
Back to top
 
IP Logged
 
boats
Frequent Elocutionist
*****
Offline



Posts: 7760
Location: Virginia
Joined: Apr 23rd, 2004
Re: case trimmers
Reply #3 - Dec 31st, 2009 at 8:21am
Print Post  
I  have two Saeco trimmers but use the Lees all most 100 %

Thing about Trimming is it's not the only case prep job that needs to be done.  I chuck a new case up in the lathe with one of Lees collet case chucks.  Turn it slow then trim with Lees tool, chamfer the inside, hold a piece of 600 paper on the outside to de-bur the mouth, then run a flash hole tool in to clean it up.

4 jobs one chucking using hand held tools from Lee.  You could do all 4 with a power drill just as easy as in the lathe.

Boats
  
Back to top
 
IP Logged
 
38_Cal
Frequent Elocutionist
*****
Offline



Posts: 2257
Location: Montezuma, Iowa
Joined: Apr 27th, 2005
Re: case trimmers
Reply #4 - Dec 31st, 2009 at 10:12am
Print Post  
I use an older Lyman hand crank tool, modified to take a power screwdriver instead of the crank.  Does fine for what little trimming needs to be done.

David
  
David Kaiser
Montezuma, IA
Back to top
 
IP Logged
 
Green_Frog
Frequent Elocutionist
*****
Offline


"It ain't easy being green"
ASSRA Life #281

Posts: 4202
Location: Lynchburg, VA
Joined: Apr 18th, 2004
Re: case trimmers
Reply #5 - Dec 31st, 2009 at 10:39am
Print Post  
Trim?  You mean you are supposed to trim those little brass things??  Roll Eyes

Froggie
  
Back to top
 
IP Logged
 
John in PA
Oldtimer
*****
Offline



Posts: 590
Location: Hollidaysburg, PA
Joined: Nov 3rd, 2009
Re: case trimmers
Reply #6 - Dec 31st, 2009 at 10:56am
Print Post  
4-D/C-H Tool and Die makes a fantastic case trimmer that uses regular shell holders and C-H pilots.  I've had one for years.  it is a workhorse.  Truly the Mother of All Case-trimmers!!

(You need to Login or Register to view media files and links)

(You need to Login or Register to view media files and links)
  
John Wells
Hollidaysburg, PA
Peabody and Peabody-Martini's Wanted!
Back to top
 
IP Logged
 
stebbinsgr
Ex Member


Re: case trimmers
Reply #7 - Dec 31st, 2009 at 11:01am
Print Post  
Look at the Lee case trimmer.  The price is half that of the others.  Also get the chamfering tool and the primer hole uniformer.  In all you will spend less than any of the others.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.6060 seconds.